-
1 circuit area
English-German dictionary of Electrical Engineering and Electronics > circuit area
-
2 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
3 trunk
-
4 supply
1.[sə'plaɪ]transitive verb1) liefern [Waren usw.]; sorgen für [Unterkunft]; zur Verfügung stellen [Lehrmittel, Arbeitskleidung usw.]; beliefern [Kunden, Geschäft]; versorgen [System]supply something to somebody, supply somebody with something — jemanden mit etwas versorgen/(Commerc.) beliefern
2) (make good) erfüllen [Nachfrage, Bedarf]; abhelfen (+ Dat.) [Mangel]2. noun1) (stock) Vorräte Pl.military/medical supplies — militärischer/medizinischer Nachschub
supply and demand — (Econ.) Angebot und Nachfrage
the blood supply to the brain — die Versorgung des Gehirns mit Blut
3)3. attrib.supply [teacher] — Aushilslehrer, der/-lehrerin die
Versorgungs[schiff, -netz, -basis, -lager usw.]* * *1. verb(to give or provide: Who is supplying the rebels with guns and ammunition?; Extra paper will be supplied by the teacher if it is needed; The town is supplied with water from a reservoir in the hills; The shop was unable to supply what she wanted.) (be)liefern2. noun1) (the act or process of supplying.) die Lieferung2) ((often in plural) an amount or quantity that is supplied; a stock or store: She left a supply of food for her husband when she went away for a few days; Who will be responsible for the expedition's supplies?; Fresh supplies will be arriving soon.) der Vorrat•- academic.ru/115302/be_in_short_supply">be in short supply* * *sup·ply1[səˈplaɪ]I. vt<- ie->1. (provide sth)to \supply an answer to a question eine Antwort auf eine Frage gebento \supply information about sth Informationen über etw akk geben▪ to \supply sth to sb arms, drugs jdm etw beschaffento be accused of \supplying drugs des Drogenhandels beschuldigt werden, wegen Drogenhandel[s] angeklagt sein2. (provide sb with sth)▪ to be supplied with sth etw erhaltento \supply sb with food jdn mit Nahrung versorgen3. (act as source) liefernthis cereal supplies plenty of vitamins dieses Getreide ist ein großer Vitaminspender4. (satisfy)to \supply a demand eine Nachfrage befriedigento \supply a requirement einer Forderung nachkommenII. na month's \supply of tablets eine Monatspackung Tablettenwater \supply Wasservorrat melectricity [or power] /water \supply Strom-/Wasserversorgung fsource of \supply Bezugsquelle f\supply and demand Angebot und Nachfrageto be in plentiful \supply im Überfluss [o reichlich] vorhanden seinto be in short \supply Mangelware sein4.▪ supplies pl (provision) Versorgung f kein pl, [Zu]lieferung f; MIL Nachschub m; (amount needed) Bedarf mto be urgently in need of medical supplies dringend medizinischer Versorgung bedürfento cut off supplies die Lieferungen einstellento cut off gas/water supplies das Gas/Wasser abstellenoffice supplies Bürobedarf m5. (amount available)6. BRIT POLto be on \supply vertretungsweise unterrichtensup·ply2[ˈsʌpl̩i]adv see supplely* * *[sə'plaɪ]1. nsupply and demand — Angebot und Nachfrage (+pl vb)
2) (= what is supplied) Lieferung fto cut off the supply (of gas, water etc) — das Gas/Wasser abstellen
our wholesaler has cut off our supply — unser Großhändler hat die Lieferungen eingestellt
3) (= stock) Vorrat mto get or lay in supplies or a supply of sth — sich (dat) einen Vorrat an etw (dat) anlegen or zulegen
to be in good supply —
our supplies are running out fresh supplies (Mil) — unser Vorrat geht or unsere Vorräte gehen zu Ende Nachschub m
office supplies — Bürobedarf m, Büromaterial nt
medical supplies — Arzneimittel pl; (including bandages) Ärztebedarf
4) (= supply teacher) Aushilfslehrer(in) m(f)2. vt1) material, food, tools etc sorgen für; (= deliver) goods, information, answer, details liefern; clue, evidence, gas, electricity liefern; (= put at sb's disposal) stellen2) (with mit) person, army, city versorgen; (COMM) beliefernshe supplies the humour in the office — sie sorgt für ( den) Humor im Büro
this supplied me with the chance... — das gab mir die Chance...
* * *supply [səˈplaı]A v/t1. a) allg Beweise, Elektrizität etc liefernb) die nötige Ausrüstung etc beschaffen, bereitstellen, sorgen fürwith mit):supply sb with sth, supply sth to s.o3. fehlende Wörter etc ergänzen4. einen Verlust etc ausgleichen, ersetzen:supply a deficit ein Defizit decken5. ein Bedürfnis befriedigen:supply a want einem Mangel abhelfen;supply the demand WIRTSCH die Nachfrage deckensupply sb’s place jemanden vertreten7. WIRTSCH nachschießen, -zahlenB s1. Lieferung f (to an akk), Zufuhr f, Beschaffung f, Bereitstellung fwith mit), Bedarfsdeckung f3. ELEK (Netz)Anschluss m4. Ergänzung f, Zuschuss m, Beitrag m5. WIRTSCH Angebot n:supply and demand Angebot und Nachfrage;be in short supply knapp sein6. meist pl Vorrat m, Lager n, Bestand m7. meist pl MIL Nachschub m, Versorgung(smaterial) f(n), Proviant m8. pl WIRTSCH Artikel pl, Bedarf m9. a) Stellvertreter(in), Ersatz mb) Stellvertretung f:on supply in Vertretung10. meist pl PARL bewilligter EtatC adj1. Versorgungs…, Liefer…, Lieferungs…:supply plant Lieferwerk n;supply-side economics pl (als sg konstruiert) angebotsorientierte Wirtschaftspolitik2. MILa) Versorgungs…:b) Nachschub…:supply base Versorgungs-, Nachschubbasis f;supply lines Nachschubverbindungen3. ELEK, TECH Speise…:supply pipe Zuleitung(srohr) f(n);supply voltage Netz-, Speisespannung f4. Aushilfs…:sup. abk1. superior2. superlative Superl.3. supplement4. supplementary zusätzl.5. supply6. supra, above* * *1.[sə'plaɪ]transitive verb1) liefern [Waren usw.]; sorgen für [Unterkunft]; zur Verfügung stellen [Lehrmittel, Arbeitskleidung usw.]; beliefern [Kunden, Geschäft]; versorgen [System]supply something to somebody, supply somebody with something — jemanden mit etwas versorgen/(Commerc.) beliefern
2) (make good) erfüllen [Nachfrage, Bedarf]; abhelfen (+ Dat.) [Mangel]2. noun1) (stock) Vorräte Pl.military/medical supplies — militärischer/medizinischer Nachschub
supply and demand — (Econ.) Angebot und Nachfrage
2) (provision) Versorgung, die (of mit)3)3. attrib.supply [teacher] — Aushilslehrer, der/-lehrerin die
Versorgungs[schiff, -netz, -basis, -lager usw.]* * *adv.liefern adv. n.Angebot -e n.Belieferung f.Lieferung f.Speisung -en (Elektr.) f.Stellvertretung f.Versorgung f.Vorrat -¨e m. (with) v.liefern v.versorgen (mit) v. v.beschaffen v.eingeben v.speisen v.versorgen v. -
5 buffer
buffer 1. COMP Pufferspeicher m (circuit); Puffer m (temporary data storage area); 2. LOGIS Puffer m -
6 terület
(DE) Areal {s}; Bereich {pl}; Domäne {e}; Feld {s}; Felder {pl}; Gau {r}; Gebiet {s}; Provinz {e}; Region {e}; Regionen {pl}; Revier {s}; Sektor {r}; Sphäre {e}; Terrain {s}; Territorie {e}; Territorium {s}; Flächenausdehnung {e}; (EN) area; azoic; bourn; bourne; circuit; corner; country; countryside; district; domain; field; ground; isthmian; land; location; pale; place; province; range; region; reptiliferous; scope; section; space; sphere; stretch; surface; territory; tract; walk -
7 шинопровод
система сборных шин
шинопровод
Устройство, представляющее собой систему проводников, состоящее из шин, установленных на опорах из изоляционного материала или в каналах, коробах или подобных оболочках, и прошедшее типовые испытания.
Устройство может состоять из следующих элементов:
- прямые секции с узлами ответвления или без них;
- секции для изменения положения фаз, разветвления, поворота, а также вводные и переходные;
- секции ответвленные.
Примечание — Термин «шинопровод» не определяет геометрическую форму, габариты и размеры проводников.
(МЭС 441-12-07, с изменением)
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
шинопровод
Жесткий токопровод до 1 кВ заводского изготовления, поставляемый комплектными секциями.
[ПУЭ]
шинопровод
Жесткий токопровод напряжением до 1000 В заводского изготовления, поставляемый комплектными секциями.
[ОСТ 36-115-85]
шинопровод
Жесткий токопровод напряжением до 1 кВ, предназначенный для передачи и распределения электроэнергии, состоящий из неизолированных или изолированных проводников (шин) и относящихся к ним изоляторов, защитных оболочек, ответвительных устройств, поддерживающих и опорных конструкций.
[ ГОСТ Р 53310-2012]EN
busway
A prefabricated assembly of standard lengths of busbars rigidly supported by solid insulation and enclosed in a sheet-metal housing.
[ http://www.answers.com/topic/busway]
busway
Busway is defined by the National Electrical Manufacturers Association (NEMA) as a prefabricated electrical distribution system consisting of bus bars in a protective enclosure, including straight lengths, fittings, devices, and accessories. Busway includes bus bars, an insulating and/or support material, and a housing.
[ http://electrical-engineering-portal.com/siemens-busway-purpose-and-definition]1.1. Шинопроводы по назначению подразделяются на:
- распределительные, предназначенные для распределения электрической энергии;
- магистральные, предназначенные для передачи электрической энергии от источника к месту распределения (распределительным пунктам, распределительным шинопроводам) или мощным приемникам электрической энергии.
1.2. По конструктивному исполнению шинопроводы подразделяются на:
- трехфазные;
- трехфазные с нулевым рабочим проводником;
- трехфазные с нулевым рабочим и нулевым защитным проводником.
2. Основные параметры и размеры
2.1. Основные элементы шинопроводов
2.1.1. Основными элементами распределительных шинопроводов являются:а) прямые секции - для прямолинейных участков линии, имеющие места для присоединения одного или двух ответвительных устройств для секций длиной до 2 м включительно, двух, трех, четырех или более - для секций длиной 3 м;
б) прямые прогоночные секции - для прямолинейных участков линий, где присоединение ответвительных устройств не требуется;
в) угловые секции - для поворотов линии на 90° в горизонтальной и вертикальной плоскостях;
г) вводные секции или вводные коробки с коммутационной, защитной и коммутационной аппаратурой или без нее - для подвода питания к шинопроводам кабелем, проводами или шинопроводом;
д) переходные секции или устройства - для соединения двух шинопроводов на различные номинальные токи или шинопроводов разных конструкций;
е) ответвительные устройства (коробки, штепсели) - для разъемного присоединения приемников электрической энергии. Коробки должны выпускаться с разъединителем, с разъединителем и с предохранителями или с автоматическим выключателем;
з) присоединительные фланцы - для сочленения оболочек шинопроводов с оболочками щитов или шкафов;
и) торцовые крышки (заглушки) - для закрытия торцов крайних секций шинопровода;
к) устройства для крепления шинопроводов к элементам строительных конструкций зданий и сооружений;2.1.2. Основными элементами магистральных шинопроводов являются:
а) прямые секции - для прямолинейных участков линий;
б) угловые секции - для поворотов линий на 90° в горизонтальной и вертикальной плоскостях;
в) тройниковые секции - для разветвления в трех направлениях под углом 90° в горизонтальной и вертикальной плоскостях;
г) подгоночные секции - для подгонки линии шинопроводов до необходимой длины;
д) разделительные секции с разъединителем - для секционирования магистральных линий шинопроводов;
е) компенсационные секции - для компенсации температурных изменений длины линии шинопроводов;
ж) переходные секции - для соединения шинопроводов на разные номинальные токи;
з) ответвительные устройства (секции, коробки) - для неразборного, разборного или разъемного присоединения распределительных пунктов, распределительных шинопроводов или приемников электрической энергии. Коробки должны выпускаться с разъединителем, с разъединителем и предохранителями или с автоматическим выключателем; секции могут выпускаться без указанных аппаратов;
и) присоединительные секции - для присоединения шинопроводов к комплектным трансформаторным подстанциям;
к) проходные секции - для прохода через стены и перекрытия;
л) набор деталей и материалов для изолирования мест соединения секций шинопроводов с изолированными шинами;
м) устройства для крепления шинопроводов к элементам строительных конструкций зданий и сооружений;
н) крышки (заглушки) торцовые и угловые для закрытия торцов концевых секций шинопровода и углов.
2.2.3. В зависимости от вида проводников токопроводы подразделяются на гибкие (при использовании проводов) и жесткие (при использовании жестких шин).
Жесткий токопровод до 1 кВ заводского изготовления, поставляемый комплектными секциями, называется шинопроводом.
В зависимости от назначения шинопроводы подразделяются на:- магистральные, предназначенные в основном для присоединения к ним распределительных шинопроводов и силовых распределительных пунктов, щитов и отдельных мощных электроприемников;
- распределительные, предназначенные в основном для присоединения к ним электроприемников;
- троллейные, предназначенные для питания передвижных электроприемников;
- осветительные, предназначенные для питания светильников и электроприемников небольшой мощности.
[ПУЭ, часть 2]
[ http://electrical-engineering-portal.com/siemens-busway-purpose-and-definition]
[ http://electrical-engineering-portal.com/standards-and-applications-of-medium-voltage-bus-duct]
Конструкция шинопровода на среднее напряжениеПараллельные тексты EN-RU
A major advantage of busway is the ease in which busway sections are connected together.
Electrical power can be supplied to any area of a building by connecting standard lengths of busway.
It typically takes fewer man-hours to install or change a busway system than cable and conduit assemblies.Основное преимущество шинопровода заключается в легкости соединения его секций.
Соединяя эти стандартные секции можно легко снабдить электроэнергией любую часть здания.
Как правило, установить или изменить систему шинопроводов занимает гораздо меньше времени, чем выполнить аналогичные работы, применяя разводку кабелем в защитных трубах.[ http://electrical-engineering-portal.com/siemens-busway-purpose-and-definition]
The total distribution system frequently consists of a combination of busway and cable and conduit.
In this example power from the utility company is metered and enters the plant through a distribution switchboard.
The switchboard serves as the main disconnecting means.Как правило, распределение электроэнергии производится как через шинопроводы, так и через проложенные в защитных трубах кабели.
В данном примере поступающая от питающей сети электроэнергия измеряется на вводе в главное распределительный щит (ГРЩ).
ГРЩ является главным коммутационным устройством.
The feeder on the left feeds a distribution switchboard, which in turn feeds a panelboard and a 480 volt, three-phase, three-wire (3Ø3W) motor.
Распределительная цепь, изображенная слева, питает распределительный щит, который в свою очередь питает групповой щиток и электродвигатель.
Электродвигатель получает питание через трехфазную трехпроводную линию напряжением 480 В.The middle feeder feeds another switchboard, which divides the power into three, three-phase, three-wire circuits. Each circuit feeds a busway run to 480 volt motors.
Средняя (на чертеже) распределительная цепь питает другой распределительный щит, от которого электроэнергия распределяется через три трехфазные трехпроводные линии на шинопроводы.
Каждый шинопровод используется для питания электродвигателей напряжением 480 В.The feeder on the right supplies 120/208 volt power, through a step-down transformer, to lighting and receptacle panelboards.
Распределительная цепь, изображенная справа, питает напряжением 120/208 В через понижающий трансформатор щитки для отдельных групп светильников и штепсельных розеток.
Branch circuits from the lighting and receptacle panelboards supply power for lighting and outlets throughout the plant.
[ http://electrical-engineering-portal.com/siemens-busway-purpose-and-definition]Групповые электрические цепи, идущие от групповых щитков, предназначены для питания всех светильников и штепсельных розеток предприятия.
[Перевод Интент]Selection of the busbar trunking system based on voltage drop.
[Legrand]Выбор шинопровода по падению напряжения.
[Перевод Интент]
Недопустимые, нерекомендуемые
Примечание(1)- Мнение автора карточкиТематики
- изделие электромонтажное
- электропроводка, электромонтаж
Обобщающие термины
Близкие понятия
- электропроводки, выполненные шинопроводами
Действия
- выбор шинопровода по...
- крепление шинопровода к опорным конструкциям
- монтаж шинопроводов
- применение шинопроводов в пожароопасных зонах
- проектирование шинопровода
- прокладка шинопровода
Сопутствующие термины
- вертикальный участок шинопровода
- горизонтальный участок шинопровода
- прямой участок шинопровода
- устройства для крепления шинопроводов
- шинопровод переменного тока на 1600 А
- электрическая сеть, выполняемая шинопроводами
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > шинопровод
См. также в других словарях:
Circuit switching — is a methodology of implementing a telecommunications network in which two network nodes establish a dedicated communications channel (circuit) through the network before the nodes may communicate. The circuit guarantees the full bandwidth of the … Wikipedia
Circuit integrity — fireproofing of cable trays in Lingen/Ems, Germany using calcium silicate board system qualified to DIN 4102 … Wikipedia
circuit — cir·cuit n 1 a: a route formerly taken by traveling judges b: a district established within a state or the federal judicial system see also the judicial system in the back matter 2 cap: the court of appeals for a circuit in the federal judicial… … Law dictionary
Circuit court — is the name of court systems in several common law jurisdictions. Contents 1 History 2 Republic of Ireland 3 United States 3.1 Federal courts of appeals … Wikipedia
circuit — [sʉr′kit] n. [ME < OFr < L circuitus, a going around, circuit < circumire < circum (see CIRCUM ) + ire, to go: see YEAR] 1. the line or the length of the line forming the boundaries of an area 2. the area bounded 3. the act of going… … English World dictionary
Circuit Gilles Villeneuve — The Hairpin (L Epingle) on Circuit Gilles Villeneuve Location Montreal, Quebec, Canada Time zone GMT −5 … Wikipedia
Circuit training — is a form of conditioning combining resistance training and high intensity aerobics. It is designed to be easy to follow and target strength building as well as muscular endurance. An exercise circuit is one completion of all prescribed exercises … Wikipedia
Circuit — Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth round the… … The Collaborative International Dictionary of English
Circuit court — Circuit Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth… … The Collaborative International Dictionary of English
Circuit of action — Circuit Cir cuit, n. [F. circuit, fr. L. circuitus, fr. circuire or circumire to go around; circum around + ire to go.] 1. The act of moving or revolving around, or as in a circle or orbit; a revolution; as, the periodical circuit of the earth… … The Collaborative International Dictionary of English
Circuit Mont-Tremblant — Location Mont Tremblant, Quebec, Canada Owner Lawrence Stroll … Wikipedia